Project Articles in Category “Member Projects”
Detail your ongoing projects here.
Knorm's Opel How To Videos
Knorm's Opel How To Videos
Volvo 240 Rear End Swap
I picked up a rear end from a 1990 Volvo 240 with a 3.73 ratio and will be putting it in my 24 valve Ascona wagon.
I drilled the axles to a 4x100 pattern today (5x108 is stock) and a G80 locker carrier will be here tomorrow.
As of now, I'm leaning toward using the Opel spring buckets with adjustable arms and a torque arm going up to the Opel center joint mount. This will allow the Opel shock mounts and panhard bar mounts to be used.
Another option was sent to me by dsmith which needs more looking into. In that GT install, the Opel springs were mounted on the Volvo trailing arms and the arms matched up to the Opel front mounts. Two links from the axle to the training arm stabilized the axle. Shock and panhard mounts were relocated.
The brake system on the rear end needs replacing. The Volvo e-brake uses brake shoes on the inside of the rotors and both were in real rough shape. Rock Auto and Advanced auto will have all the Volvo brake parts here by Thursday.
I installed the Eaton G-80 locker…
I drilled the axles to a 4x100 pattern today (5x108 is stock) and a G80 locker carrier will be here tomorrow.
As of now, I'm leaning toward using the Opel spring buckets with adjustable arms and a torque arm going up to the Opel center joint mount. This will allow the Opel shock mounts and panhard bar mounts to be used.
Another option was sent to me by dsmith which needs more looking into. In that GT install, the Opel springs were mounted on the Volvo trailing arms and the arms matched up to the Opel front mounts. Two links from the axle to the training arm stabilized the axle. Shock and panhard mounts were relocated.
The brake system on the rear end needs replacing. The Volvo e-brake uses brake shoes on the inside of the rotors and both were in real rough shape. Rock Auto and Advanced auto will have all the Volvo brake parts here by Thursday.
I installed the Eaton G-80 locker…
Read More
2
Installing a Pertronix Ignitor
Article by Otto Bartsch
Simplest installation of electronically triggered ignition in a GT is to purchase and use Pertronix/Hot-Spark trigger and stock coil. Here's how:
1. Remove cap, rotor, points and condenser with green wire from distributor and disconnect green "condenser/points" wire from coil. Leave everything else connected as-is.
2. Install Pertronix/Hot-Spark trigger amp module where points were, do not tighten mounting screws yet.
3. Run red and black module wires out "points wire" hole in side of distributor and install grommet in "points wire" hole, leaving a bit of slack on both wires inside of distributor.
4. Push black plastic magnet unit onto distributor shaft and seat over points cam.
5. Adjust trigger amp module to magnet unit clearance using clear plastic gauge that is provided and tighten trigger module screws.
6. Replace rotor and cap . . . you're now done with the distributor.
7. Connect black Pertronix/Hot-Spark wire to coil contact from which you removed the green…
Simplest installation of electronically triggered ignition in a GT is to purchase and use Pertronix/Hot-Spark trigger and stock coil. Here's how:
1. Remove cap, rotor, points and condenser with green wire from distributor and disconnect green "condenser/points" wire from coil. Leave everything else connected as-is.
2. Install Pertronix/Hot-Spark trigger amp module where points were, do not tighten mounting screws yet.
3. Run red and black module wires out "points wire" hole in side of distributor and install grommet in "points wire" hole, leaving a bit of slack on both wires inside of distributor.
4. Push black plastic magnet unit onto distributor shaft and seat over points cam.
5. Adjust trigger amp module to magnet unit clearance using clear plastic gauge that is provided and tighten trigger module screws.
6. Replace rotor and cap . . . you're now done with the distributor.
7. Connect black Pertronix/Hot-Spark wire to coil contact from which you removed the green…
Read More
2
Goin Manta Projects
My Blog for all Opel related adventures, projects, etc..
Tips on assembling a motor, Bosch EFI, Opel values, etc.. etc.. etc..
With over 30 years of tinkering with these things from my first car in High School a 1971 Kadett in 1985 to Today and my 1992 Senator B... and everything inbetween, hopefully my mistakes will help you know what to know not to do..
Tips on assembling a motor, Bosch EFI, Opel values, etc.. etc.. etc..
With over 30 years of tinkering with these things from my first car in High School a 1971 Kadett in 1985 to Today and my 1992 Senator B... and everything inbetween, hopefully my mistakes will help you know what to know not to do..
Read More
